A Mercer company - serving Miami, FL

Boral Ridge Vent Installation Nationwide

Metal roofingMetal roofing
Architectural shinglesArchitectural shingles
Tile roofingTile roofing
GAFGAF
Owens CorningOwens Corning
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

Your new roof for as low as$159/month*On approved credit; ask for current terms
Get your free estimate

Boral Ridge Vent Installation: The Miami Owner’s Guide

Boral ridge vent installation in Miami typically runs $850 – $1,650 for a standard single-family home, depending on linear footage and the condition of the existing roof decking at the ridge line. Most Boral-compatible ridge vent replacements are completed in a single visit, and we keep the most common profiles on the truck. Homeowners usually discover the part has failed after a Miami afternoon storm, when they notice warm air trapped in the attic, peeling paint near the ceiling, or a ridge vent that has cracked and separated from the shingles. The ridge vent is the last line of defense for attic airflow, and when it fails in a climate like ours, the attic heat and humidity start working against everything underneath.

Call (850) 753-2996

Which Boral Models This Applies To

Boral’s ridge vent systems are designed to integrate with their concrete and stone-coated steel tile profiles, and the installation methods are not interchangeable with asphalt shingle ridge vents. The two most common lines we work with in Miami are the Boral VitaTile and the Boral StormLine Series, both of which use a vented ridge profile that follows the tile’s contour. The critical compatibility gotcha is the profile pitch: a VitaTile ridge vent will not seat correctly on a StormLine tile without an adapter, because the tile crown height differs by nearly half an inch. If a previous roofer installed a generic vent on a Boral tile, it’s often the source of the failure you’re seeing now.

OEM Boral ridge vent materials are available through regional tile distributors, but lead times in Miami can stretch to two or three weeks for less common color matches. We typically recommend OEM whenever the tile color is still in production and a close match is recoverable. For discontinued colors, a quality aftermarket vent from a manufacturer like GAF or CertainTeed can work structurally, but the color and profile matching is where a careful installer earns the money. We walk the roof, measure the tile crown, and confirm the part number before we order anything. We are an independent Miami roofing contractor and not affiliated with Boral, but we install and repair their systems regularly.

Explore

Styles & brands we work with

Architectural shingles
Architectural shingles
Metal roofing
Metal roofing
Tile roofing
Tile roofing
GAF
GAF
Owens Corning
Owens Corning
Flat & low-slope
Flat & low-slope

Signs Your Boral Ridge Vent Installation Is Failing

  • Separated vent sections at the ridge line. Miami’s heat cycles cause the plastic or metal vent material to expand and contract, and the joints eventually open up. Once water gets under the vent, it travels along the ridge board and shows up as ceiling stains in interior rooms.
  • Crushed or flattened vent profile. Boral tile is heavy, and if the vent wasn’t properly supported or was stepped on during a past repair, the airflow channel collapses. The attic stops breathing, and the upstairs rooms start heating up noticeably in the afternoon.
  • Missing end caps or exposed foam filter. The end caps keep wind-driven rain out of the vent’s open ends. In Miami’s summer storms, a missing end cap will push water directly into the attic, usually showing up as a leak near the gable wall.
  • Black streaks or moisture staining on the vent itself. This is often a sign that the vent is drawing moisture up from the attic rather than exhausting it, usually because the intake ventilation at the soffit is blocked or undersized for the vent’s airflow rating.
  • Tile slippage at the ridge. When the vent base fails, the nail line loosens, and the Boral tiles along the ridge begin to shift. You may see a slightly wavy ridge line from the street, which means the vent’s anchoring has already started to go.

Replacement Cost & What’s Included

For a standard single-story Miami home with 30 to 40 linear feet of Boral ridge vent, a full replacement typically lands between $850 and $1,350. Two-story homes with steep roof pitches run higher, usually $1,200 to $1,650, because of increased staging, safety equipment, and labor. The price includes removing the old vent, inspecting the ridge board and top course of tile, replacing any rotted decking at the ridge (up to a small allowance), installing the new vent, and sealing all transitions. The parts themselves are usually $180 to $450 of that total, with the rest being labor and disposal.

We give you a written price before any work starts, and that price doesn’t change unless we find rotted decking or structural issues that require additional work, in which case we walk you through it before proceeding. Every Boral ridge vent installation we do is covered by our 365-Day Done Right Promise, meaning if anything isn’t right within a year, we come back and make it right at no charge.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

DIY or Call Us?

Working on a Boral tile roof is different from walking asphalt shingles. The tiles fracture easily under foot traffic, the roof pitch is often steeper than homeowners expect, and the ridge line is the most exposed position on the entire roof. A fall from a single-story ridge is enough to cause serious injury, and Boral tile shards make the surface slick in the morning dew we get year-round in Miami. We recommend limiting your involvement to a visual check from the ground or a ladder placed at the eave, looking for the signs we covered above. The actual removal and replacement belongs to a trained crew with proper fall protection and experience handling tile without cracking it.

What you can safely do is take photos of the vent from the ground and note where you’re seeing separation or staining. That helps us quote the job accurately before we send anyone up. For the installation itself, call us at (850) 753-2996 and we’ll schedule a roof inspection with a written estimate.

FAQs

Call Mercer Roofing Co Miami for Your Boral Ridge Vent

A roof shouldn’t be something you worry about – that’s our job. If you suspect your Boral ridge vent is failing, or you’ve already spotted water staining near the ridge line, call us at (850) 753-2996 for a free estimate. Grant Whitlock or one of our background-checked, photo-badged technicians will walk the roof, show you exactly what’s happening, and give you a written price before any work begins. We answer the phone with a live person, day or night, and every repair is backed by our written guarantee.

Written by Grant Whitlock, Owner, Mercer Roofing Co Miami at Mercer Roofing Co Miami, serving Miami and nearby areas.

Need Roofing help in Miami? Licensed & insured · Written quotes before work starts response · free estimates
Call (850) 753-2996
Local Service Coverage

Request a Free Estimate in Miami

Tell us what you need - Mercer Roofing Co Miami responds fast. No obligation.

By submitting this form, you accept our Privacy Policy and authorize us to contact you by call, text, or email concerning your request, including by the partner businesses that may perform the service.

Prefer to text? Text Now
Call Now - 24/7 Dispatch